Nanovna F V2 50kHz-3GHz 4.3inch Vectory Network Analyzer Hf VHF UHF Antenna Analyzer

Product Description

Product Description

 

NanoVNA-V2 portable vector network analyzer is a new generation of products developed based on OwOComm's S-A-A-2 design with large performance upgrade. The measuring range is extended to 50KHz-3000MHz, and the dynamic range is larger, reaching 80db. It can be used to debug the diplers of UV frequency, and the measurement is more accurate. More practical simple flexible and fast operation interface. This Xiaoyan second beats the performance of all versions of this NanoVNA series on the market.

It can test the standing wave impedance of the antenna, it can also test the insertion loss isolation of the filter, standing wave can also test the attenuation shortening factor of the cable, phase can also test the amplification factor of the antenna amplifier, it has the function of the frequency meter, it can also measure the length of the cable, the group delay function is powerful, and the most important is that it can also debug the dipler of the frequency of the uv segment, highly recommended, Kill any other version of NanoVNA on the market. Highly recommended!!


Product performance:
1. Measurement frequency range: 50KHz-3000MHz;

2. Rf output power: -9dbm (error within 1GHz: plus or minus 1db);

3. Frequency accuracy: < 0.5ppm

4.S21 dynamic range: 70dB (1.5GHz), 60dB (3GHz)

5.S11 dynamic range: 50dB (1.5GHz), 40dB (3GHz)



6.2 Port return loss: 20dB typ (1.5GHz), 13dB min (3GHz)

7.USB interface: USB Type-C communication mode: CDC (serial)

8. Number of calibration points: 101

9. Number of scanning points: 101 points

10. Show trace: 4 trace

11. mark: 4 mark points (mark bar can be moved up and down the screen)

12. Save the Settings: 5 (after saving, it can be directly called when the next boot is used, without re-calibration, and the saved parameters before the last shutdown will be automatically called when the next boot is started)

13. Scanning time: about 1.9s/1 time (50kHz ~ 3000MHz full band)

14. Can measure S parameters, voltage standing wave ratio SWR Smith circle diagram Phase diagram, group delay,...... ;

15.4.3 inch IPS LCD screen, IPS TFT (800x480) viewing Angle close to 180°, long-term use does not hurt eyes;

16. The aluminum alloy case effectively shields electromagnetic interference, making the S21 better than 80dB dynamic range in 1GHz

17. Compact design, body size 125mm*75mm*20mm, compact and portable;

18. The RF interface is SMA, which is convenient to connect all kinds of tested parts;

19. Use 5000mAh ultra-large capacity lithium battery, the battery life can reach 7 hours;

20. Full touch screen design, while supporting 3 side buttons, flexible and convenient operation;

21. Support Chinese and English menu switching;

22. Support screen brightness adjustment;

23. Upgrade firmware through virtual U disk, no programmer required, only a USB cable can upgrade firmware;

22. Extend a USB power output interface, 5V/1A output (can be used as a charging bank);

24. Using high current 2A charging IC, the charging time is shorter;

25. Support the host computer, can use the computer as the display operation interface;

26. Weight of plastic packing box: 400g



Product standard configuration

 Host x1

SMA-JJ RG405 connection cable 20CM x2 (NanoVNA-V2 is a standard SMA female interface, outer screw and inner hole)

1 set of calibration parts (50Ω standard load x1, open circuit calibration part x1, short circuit calibration part x1, using the attached calibration part, the instrument can obtain good measurement results after calibration data, if the measurement conditions are changed, such as adding the adapter wire, modifying the frequency range, you need to recalibrate and store the parameters in 0-4. All parameters can be called out through the "callback" function, if the requirements are not very strict, you can carry out a full-band calibration work, change the frequency range can also be used, but there will be a certain error at this time)

SMA-F double hole x1 (that is, SMA double pass)

SMA elbow outer screw inner hole turn inner screw inner needle x1
Type-C data cable x1

SMA all-copper RF converter N/SMA-KJ x1(add)

 Stylus x1

 At the same time, it comes with a set of packaging boxes, with pearl cotton protection instruments and parts.